• From a container size of 10 l the material has to be mechanically stirred for example with LOBA Paint mixer.
• The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
• The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% - 65%, material temperature +18°C - + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
• In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
• Transfer material to a LOBA varnish bucket before applying.
• Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
• This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems
• Shake the contents well.

Thinner / Mixing

The product is ready for use and must not be reduced!

Application tool / application rate

Trowel application: LOBA Trowel / approx. 20 ml/m² (50 m²/l)
Roller and oilbrush application: LOBA Oil Roller Microfibre 60-80 or LOBA Oil Brush / approx. 40-60 ml/m² (20 m²/l).

Drying time

• Carefully walkable and recoatable after 8 hours.
• Light stress after 24 hours.
• Full Stress and coverage after 10 days.
• The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
• Drying times are valid for +20°C and 50% relative humidity.

Intermediate sanding

Within 24 hours it can be recoated without, then only with an intermediate sanding. An intermediate sanding with LOBASAND sanding fleece and underlaid LOBASAND hook & loop strips before the final coat can improve the final visual result.

Trowel and roller application:

For wooden floors.

• Apply HardwaxOil carefully in sections using a LOBA trowel.
• Immediately equalise with a single-disc machine and underlaid LOBASAND SpecialPad beige.
• Dry minimum 8 hours, maximum 24 hours.
• Roll HardwaxOil thinly and evenly with LOBA Oil Roller Microfiber 60-80.
• For highly absorbent substrates, an additional roll application may be necessary to achieve homogeneous fullness after an intermediate sanding with a LOBA GridPad and hook & loop strips placed underneath..
  

Roll application:

For wooden and cork floors.

• Apply HardwaxOil thinly and evenly with the LOBA Oil Roller Microfiber 60-80/LOBA Oil Brush.
• Dry minimum 8 hours, maximum 24 hours.
• Perform intermediate sanding with a LOBA GridPad and hook & loop strips placed underneath and remove dust.
• Apply HardwaxOil thinly and evenly with the LOBA Oil Roller Microfiber 60-80/LOBA Oil Brush.
• For highly absorbent substrates, an additional roll application may be necessary to achieve homogeneous fullness after an intermediate sanding with a LOBA GridPad and hook & loop strips placed underneath.

Suitable product combinations

Versatile color design in combination with:

• ImpactOil Color
• Markant Color
  
  Follow technical data sheet of the product.

Important information

Trowel applications are only possible with joint-sealed wooden flooring. Oil that penetrates joints will not dry completely over a long period.Keep soaked cloths, pads and other tools in closed containers. Moisten oil in combination with sanding dust, fabric cloths and so on with water or store in a sealable bucket and dispose of in a fire-safe manner, since otherwise there is a risk of self-ignition.